Showing posts with label teaching basket-making. Show all posts
Showing posts with label teaching basket-making. Show all posts

Sunday, October 21, 2012

Possibilities for teaching basketry classes

 The Guild I belong to, The Ottawa Valley Weavers and Spinners Guild, has lots of spinning and weaving classes, but a shortage of basket-making classes. Today, I and two other basket-makers from the Guild, received a special appeal to offer basket-making classes in 2013. I have taught the occasional class before, so I responded favourably this time.
I offered my skills in offering classes in 1. Making a rib basket as above, or 2. Making a Market Basket as above. The first class would likely see the basket completed in one day (from 10 to 4 00) while the second would likely take two days. I would supply all the tools and materials with one exception for the Market Basket. There I would ask participants to bring around 30 clothes pegs. I (or I should say Anne)   have enough pegs on hand for about two baskets, not six or more that could be needed.

Tuesday, February 9, 2010

Day 1 of Tutorial for making a basketry hot air balloon



Cut nine pieces of cane 8" long. Soak them. Cut 36 pieces of cane 20" long. Remove the nine from the water and place these to soak. Add several long pieces of finer cane to soak too. These will be the weavers. Pierce five of the 8" pieces at their mid-point with an awl or bodkin. Have all the pieces oriented the same way with their natural curve.



Take the other four 8" pieces and thread them through the five, allowing the natural curve to let them sit as shown. On one side of the cross use the awl to make space for the ends of two of the finer weavers.





Weave three rounds of twining weave around the cross shape, packing it as tightly as you can.









Begin to separate the spokes with the twining weave on the fourth round. Where there are four stakes, separate into pairs, where there are five, separate into a pair, a single and a pair. Weave three more rounds and then separate into singles. Continue weaving until you reach the ends of the stakes. Insert the two weavers into the weaving. Then trim of the ends.







To mould this shape, I wove on my lap, bending the stakes as I wove. I then used an awl to piece the top of the balloon's dome so I could insert a bolt to hold the ceraminc knob I chose for this basket.






I then took the 36 20" stakes and inserted them as far as possible into the dome placing two at each stake end. I then placed the dome upside down on a pyrex jug, and gave it some stability by placing a weight, a rock, inside it.








To help mould the balloon shape, I tied a string around the stakes. I then wove five rows of three rod waling both to add structural strength to the design but also to give some textural variation to the weave.









The last stage in Day 1 was the weave an arrow pattern using three rod waling and reverse three rod waling. For this I added colour. One weaver was red, a second white and the third blue. I wove one round of three rod waling, weaving over two, behind one and out.




I finished the first row and cut off the ends.










For the next row of reverse waling, I began at a different place placing the red weaver over a red weaver in the row below, the white over the white and the blue over the blue. To weave I took each weaver under two behind one and out instead of over two behind one and out. I checked as I went along that the arrow pattern was being formed.


I wove a total of six rows for the arrow weave alternating waling and reverse waling.
This took around two hours to this stage.












Friday, November 27, 2009

Another busy day

The day started at 8 00 am when the contractor who is to start the excavating on Monday arrived to give us an estimate about the extra costs of excavating on our land to replace the storm sewer. My heart sank when he mentioned that since the storm sewer is located below the sanitary sewers so these would have to be replaced too. His estimate, of just over $3000 including replacing the pipes, was a very pleasant surprise. Later in the day he emailed the contract to us. He estimates the total job will take two days only.

Most of the rest of the morning was spent in readying the Studio for Sunday's teaching class and for Adrian's 40th birthday party on Saturday.

At tea-break time, Anne pointed out an article in the local weekly newspaper that said the Ottawa City Council had approved increasing the plumbing grant to $7500 so that sump pumps could be installed where needed in areas with a high flood risk. We are in such an area. We had received a letter approving the installation of such a pump, but we had balked at it because the expense was not covered. Now we needed to revise our thoughts.

As it happened, the Dennis, the plumber from Plumbing Now was scheduled to come at 1 00 pm to finalise his bill for work done on the back-up valves and to receive payment. I contacted the engineer who had recommended that the sump pump be installed and discussed where it should be located. We already had approval for the cost estimate from Plunbing Now.

When Dennis arrived I was able to discuss the locating of the pump with some understanding. Dennis will contact the excavation company and be here at 8 00 am on Monday morning. In that way the external excavation needed for the sump pump and its ancillary pipes will be done when all the other excavation takes place. Dennis even thinks his crew could finish the installation inside on Tuesday. (Given his timelines in the past, we will be pleasnatly surprised if this happens.)

After Dennis left, Anne said, "You will be very happy about this email." I had an order for four baskets from a past customer of mine in Brooklyn, New York. After lunch I packed these baskets, took them to the mail, and returned to give the customer her 20% discount for sales made during my pre-Christmas sale. (That sale ends on November 30th.) This was a nice way to end the day.

Friday, November 20, 2009

Readying my studio for Sunday's basket-making class

On Sunday I will welcome two students to my basketry studio where they will spend the first of two days learning how to make a sewing basket. One student will share the large table with me while the second will sit at the card table.






My storage room has several hanks of rattan cane ready for the students to choose from.








Other selections may be made from the dyed flat cane and other materials in that area.







In my work space I have pre-cut cane ready to begin as well as the tools of the trade. For the basic design of the sewing basket, I copied instructions from Flo Hoppe's "Wicker Basketry" for her Bargello Design basket. This I find makes a good body for a sewing basket. I will use the instructions as a guide only. Each student may use different design elements other than the bargello design. I will demonstrate a number of weaving designs as I teach them. In a lesson I learned from last Sunday's class, the instructions are enclosed in a transparent plastic folder. By the end of the day the instructions will not be a sodden mass of pulp!



Each student has a bucket in which to place cut off pieces of cane, a rock or half house brick to act as a weight when weaving the sides of the basket, a spray bottle to keep the material damp through the day, scissors and cutters, a small tape measure, needle nosed pliers, a towel, pre-cut cane, a bodkin or awl, and a small plastic ruler. On the floor by the tables will be two large totes with water in which to soak the cane.
I am looking forward to this day